Just how do you really feel when it comes to Installing A Bathtub?
Mounting a tub isn't exactly brain surgery, but it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently available, the task can relocate speedily; if you have to open a wall surface to remove the old bathtub and position the new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the job as well as fit trying it. As opposed to employing a contractor to take over a halfway-completed job, it is better to think about using one before you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you set up a new bath tub in your restroom if you have actually already gotten a brand-new bathtub and do not require to change the plan of your previous supply of water pipelines.
Your tools and also material list must make up the following:
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the tub in the needed position. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression join; then do the same for the other tap.
Switch on the supply of water and check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bath tub and also check the overflow outlet and the normal outlet for leaks.
Ultimately, repair the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the bath tub ought to wait till the bathtub has been used at the very least when as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location in between the tap as well as the sink. Secure the tap in place with the supplier supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The previous type must be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, bring about complications with wetness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and fittings. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can crack fairly early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily offered on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that page about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the web. Sharing is good. One never knows, you could be doing someone a favor. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Request An Estimate